Applications
| Plants and Refineries |
| Transmission Lines |
| Power Plants / Nuclear Plants |
| Chemical Plants |
| Waste Water Systems |
| Tanks and Towers |
| Fan Systems |
| Cooling Towers |
| Pumps and Pump Stations |
| Mines |
| Deep Shaft and Tunnel Lining |
| Gas and Electric Industry |
| Beverage and Food |
| Corroded Substrates |
| Sewer, Lift Stations and Clarifiers |
| Piping Systems |
| Cooling Lines |
| Steam Plants |
| Marine / Off Shore Platforms |
| Wash-Down and Finishing Plants |
IRIDIUM WRAP®
Structural Carbon Fiber/Epoxy Reinforcement System
Prevention and Repair of Corroded and Damaged Piping Systems and Infrastructure
Standard Kit Sizes – Each Kit comes with IR-250HT/350HT or 450HT – Epoxy Resin/Hardener and Primer
2 in X 150 ft (5 cm X 46 m)
4 in X 150 ft (10 cm X 46 m)
6 in X 150 ft (15 cm X 46 m)
12 in X 300 ft (30.5 cm X 91 m)
24 in X 300 ft (61 cm X 91 m)
Kit Sizes can be customized as needed
IRIDIUM WRAP® is engineered to provide strength that enables a pipe to be restored to maximum allowable operating pressure (MAOP) without system shutdown. The system is comprised of three components, each thoroughly and independently tested. The first component is an epoxy primer, which promotes bonding to the substrate and load transfer from the internal pressure of the infrastructure to the composite repair. The second component is the thoroughly tested bi-directional woven carbon-fiber material, which provides reinforcement in the hoop and axial directions and is the strongest available non-metallic repair material on the market. The third component in the system is the epoxy resin, which allows for uniform loading throughout the entire composite wrap. For repairs that require surfaces to be modified (e.g. heavy corrosion or dents), the Iridium Wrap High Modulus Filler (HMF) can be applied. These components form a composite system that is stronger than steel. The structural system forms a pipe around a pipe, and each successive wrap increases the pressure rating.
IRIDIUM WRAP® requires an engineering assessment to compile service information such as substrate material, wall loss, operating temperature, pressure ranges and environment exposure. Iridium Technologies software analyzes this information to determine the number of wraps required for each pipe repair.
IR-250HT – STANDARD TEMPERATURE
IRIDIUM WRAP IR-250HTA Resin with IR-250HTB Hardener is a moderate work life, medium viscosity epoxy resin system that produces a durable composite repair when combined with the IRIDIUM WRAP Carbon Fiber. This resin system features a convenient 4 to 1 mix ratio by volume, low odor and a high heat deflection temperature; all of which make this resin and hardener combination an excellent choice for hand lay-up work for critical infrastructure repair.
IR-350HT – HIGH TEMPERATURE
IRIDIUM WRAP IR-350HTA Resin with IR-350HTB Hardener is a moderate work life, medium viscosity epoxy resin system that produces a durable composite repair when combined with the IRIDIUM WRAP Carbon Fiber. Resin system is an unfilled epoxy laminating system designed for use where temperatures may reach 350°F. This resin system features a convenient 4 to 1 mix ratio by volume, low odor and a high heat deflection temperature; all of which make this resin and hardener combination an excellent choice for hand lay-up work at elevated temperatures. The system gels at room temperature, but a post cure is required achieve ultimate properties. The medium viscosity and reactionary chemistry assure maximum wet-out of glass, carbon and Kevlar® fibers.
IR-450HT – ULTRA-HIGH TEMPERATURE
IRIDIUM WRAP IR-450HTA Resin with IR-450HTB Hardener is a moderate work life, medium viscosity epoxy resin system that produces a durable composite repair when combined with the IRIDIUM WRAP Carbon Fiber. Resin system is an unfilled epoxy laminating system designed for use where temperatures may reach 450°F. This resin system features a convenient 5 to 1 mix ratio by volume, low odor and a high heat deflection temperature; all of which make this resin and hardener combination an excellent choice for hand lay-up work at elevated temperatures. The system gels at room temperature, but a post cure is required achieve ultimate properties. The medium viscosity and reactionary chemistry assure maximum wet-out of glass, carbon and Kevlar® fibers.
IR-700HT – ULTRA-HIGH TEMPERATURE
IRIDIUM WRAP IR‐700‐UHT is a toughened high temperature prepreg resin carbon fiber system. It is ideally suited for the repair of structural composite components that must maintain dimensional stability under severe operating conditions. It has a continuous service temperature of 750°F and can operate at up to 1,200°F for short intermittent periods. Prepreg sizes are custom made to fit repair needs to reduce time and waste.
diamondwrap diamondwrap diamondwrap diamondwrap diamondwrap diamondwrap diamondwrap diamondwrap A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+ A+A+ A+ A+ A+ A+ A+ A+
IRIDIUM WRAP SUB-SEA
Structural Carbon Fiber/Epoxy Reinforcement System Prevention and Repair for Underwater Corroded and Damaged Piping Systems and Infrastructure
- Applicable for subsea pipelines, risers, and piping systems
- Exceptional adhesion to virtually any underwater substrate
- Restores pipe strength to MAOP
- Prevents future external corrosion
- Strong chemical and saltwater resistance
TITANIUM WRAP
Structural Fiberglass/Epoxy Reinforcement System
Prevention and Repair of Corroded and Damaged Piping Systems and Infrastructure
Standard Kit Size – Each Kit comes with TI-250HT/350HT or 450HT – Epoxy Resin and Hardener
12 in X 150 ft (30.5 cm X 46 m)
TITANIUM WRAP® is engineered to provide strength that enables a pipe to be restored to maximum allowable operating pressure (MAOP) without system shutdown. The system is comprised of two components, each thoroughly and independently tested. The first component is the thoroughly tested Biaxial stitched fiberglass material, which provides reinforcement in the hoop and axial directions and is among the strongest available non-metallic repair material on the market. The second component in the system is the epoxy resin, which allows for uniform loading throughout the entire composite wrap. For repairs that require surfaces to be modified (e.g. heavy corrosion or dents), the Titanium Wrap High Modulus Filler (HMF) can be applied.
TITANIUM WRAP® requires an engineering assessment to compile service information such as substrate material, wall loss, operating temperature, pressure ranges and environment exposure. Iridium Technologies software analyzes this information to determine the number of wraps required for each pipe repair.
TI-250HT – STANDARD TEMPERATURE
Titanium Wrap TI-250HTA Resin with TI-250HTB Hardener is a moderate work life, low viscosity epoxy resin system that produces a durable composite repair when combined with the TITANIUM WRAP Fiberglass. This resin system features a convenient 4 to 1 mix ratio by volume, low odor and a high heat deflection temperature; all of which make this resin and hardener combination an excellent choice for hand lay-up work for critical infrastructure repair.
TI-350HT – HIGH TEMPERATURE
Titanium Wrap TI-350HTA Resin with TI-350HTB Hardener is a moderate work life, low viscosity epoxy resin system that produces a durable composite repair when combined with the TITANIUM WRAP Fiberglass. Resin system is an unfilled epoxy laminating system designed for use where temperatures may reach 350°F. This resin system features a convenient 4 to 1 mix ratio by volume, low odor and a high heat deflection temperature; all of which make this resin and hardener combination an excellent choice for hand lay-up work at elevated temperatures. The system gels at room temperature, but a post cure is required achieve ultimate properties. The medium viscosity and reactionary chemistry assure maximum wet-out of glass, carbon and Kevlar® fibers.
TI-450HT – ULTRA-HIGH TEMPERATURE
Titanium Wrap TI-450HTA Resin with TI-450HTB Hardener is a moderate work life, low viscosity epoxy resin system that produces a durable composite repair when combined with the TITANIUM WRAP Fiberglass. Resin system is an unfilled epoxy laminating system designed for use where temperatures may reach 450°F. This resin system features a convenient 5 to 1 mix ratio by volume, low odor and a high heat deflection temperature; all of which make this resin and hardener combination an excellent choice for hand lay-up work at elevated temperatures. The system gels at room temperature, but a post cure is required achieve ultimate properties. The medium viscosity and reactionary chemistry assure maximum wet-out of glass, carbon and Kevlar® fibers.
clockspring clockspring clockspring clockspring clockspring clockspring clockspring clockspring clockspring
diamondwrap diamondwrap diamondwrap diamondwrap diamondwrap diamondwrap diamondwrap diamondwrap
TITANIUM FLEXWRAP
Standard and Narrow Width Structural Fiberglass/Epoxy Reinforcement System
Prevention and Repair of Corroded and Damaged of Small and Larger Piping Systems and Infrastructure
Excellent for smaller piping systems with tight bends, radius and hard to reach areas
Standard Kit Sizes – Each Kit comes with TI-250HT/350HT or 450HT – Epoxy Resin and Hardener
2 in X 75 ft (5 cm X 23 m)
4 in X 100 ft (10 cm X 30 m)
6 in X 150 ft (15 cm X 46 m)
8 in X 100 ft (20 cm X 30 m)
12 in X 150 ft (30.5 cm X 46 m)
TITANIUM FLEXWRAP® is engineered to provide strength that enables a pipe to be restored to maximum allowable operating pressure (MAOP) without system shutdown. The system is comprised of two components, each thoroughly and independently tested. The first component is the thoroughly tested Quadaxial stitched fiberglass material, which provides reinforcement in the hoop and axial directions and is among the strongest available non-metallic repair material on the market. The second component in the system is the epoxy resin, which allows for uniform loading throughout the entire composite wrap. For repairs that require surfaces to be modified (e.g. heavy corrosion or dents), the Titanium Wrap High Modulus Filler (HMF) can be applied.
TITANIUM FLEXWRAP® requires an engineering assessment to compile service information such as substrate material, wall loss, operating temperature, pressure ranges and environment exposure. Iridium Technologies software analyzes this information to determine the number of wraps required for each pipe repair.
TFW-250HT – STANDARD TEMPERATURE
Titanium Flexwrap TI-250HTA Resin with TI-250HTB Hardener is a moderate work life, low viscosity epoxy resin system that produces a durable composite repair when combined with the TITANIUM FLEXWRAP Fiberglass.
TFW-350HT – HIGH TEMPERATURE
Titanium Flexwrap TI-350HTA Resin with TI-350HTB Hardener is a moderate work life, low viscosity epoxy resin system that produces a durable composite repair when combined with the TITANIUM FLEXWRAP Fiberglass. Resin system is an unfilled epoxy laminating system designed for use where temperatures may reach 350°F.
TFW-450HT – ULTRA-HIGH TEMPERATURE
Titanium Flexwrap TI-450HTA Resin with TI-450HTB Hardener is a moderate work life, low viscosity epoxy resin system that produces a durable composite repair when combined with the TITANIUM FLEXWRAP Fiberglass. Resin system is an unfilled epoxy laminating system designed for use where temperatures may reach 450°F.
TURBO WRAP
Cost Effective Structural Fiberglass/Epoxy Reinforcement System
Repair of Corroded and Damaged of Piping Systems and Infrastructure
Standard Kit Size – Each Kit comes with TW-250HT/350HT or 450HT – Epoxy Resin and Hardener
12 in X 150 ft (30.5 cm X 46 m)
TURBO WRAP® is engineered to provide mechanical repair of corroded and damaged Infrastructure. Turbo Wrap is the fastest way to stop your critical systems from further corrosion and provide mechanical repair. Avoid system shutdowns and engineering assessments by applying Turbo Wrap throughout your critical areas. Gain 50% or more of the life by preventing corrosion. Turbo Wrap is comprised of two components, each thoroughly and independently tested. The first component is the thoroughly tested Triaxial stitched fiberglass material, which provides reinforcement in the hoop and axial directions and is among the strongest available non-metallic repair material on the market. The second component in the system is the epoxy resin, which allows for uniform loading throughout the entire composite wrap. For repairs that require surfaces to be modified (e.g. heavy corrosion or dents), the Titanium Wrap High Modulus Filler (HMF) can be applied.
TW-250HT – STANDARD TEMPERATURE
Turbo Wrap TW-250HTA Resin with TW-250HTB Hardener is a moderate work life, low viscosity epoxy resin system that produces a durable composite repair when combined with the TITANIUM FLEXWRAP Fiberglass.
TW-350HT – HIGH TEMPERATURE
Turbo Wrap TW-250HTA Resin with TW-250HTB Hardener is a moderate work life, low viscosity epoxy resin system that produces a durable composite repair when combined with the TITANIUM FLEXWRAP Fiberglass. Resin system is an unfilled epoxy laminating system designed for use where temperatures may reach 350°F.
TW-450HT – ULTRA-HIGH TEMPERATURE
Turbo Wrap TW-250HTA Resin with TW-250HTB Hardener is a moderate work life, low viscosity epoxy resin system that produces a durable composite repair when combined with the TITANIUM FLEXWRAP Fiberglass. Resin system is an unfilled epoxy laminating system designed for use where temperatures may reach 450°F.
TITANIUM HYDROWRAP
Structural Fiberglass/Water Activated Urethane Reinforcement System
Prevention and Repair of Corroded and Damaged Piping Systems and Infrastructure
Standard Sizes
2 in X 5 ft (5 cm X 1.5 m) 2 in X 15 ft (5 cm X 4.6 m)
3 in X 9 ft (7.6 cm X 2.7 m) 3 in X 30 ft (7.6 cm X 9.14 m)
4 in X 15 ft (10 cm X 4.6 m) 4 in X 20 ft (10 cm X 6.1 m)
4 in X 30 ft (10cm X 9.14 m) 4 in X 60 ft (10cm X 10.3 m)
6 in X 30 ft (15 cm X 9.14 m) 8 in X 30 ft (20 cm X 9.14 m)
10 in X 30 ft (25.4 cm X 9.14 m) 10 in X 60 ft (25.4 cm X 10.3)
Titanium HydroWrap (THW)
TITANIUM HYDROWRAP® is engineered to provide strength that enables a pipe to be restored to maximum allowable operating pressure (MAOP) without system shutdown. The system is comprised of water curing urethane resin impregnated in a biaxial fiberglass, thoroughly and independently tested. TITANIUM HYDROWRAP® system, is the selection of Biaxial Fiberglass material, which provides reinforcement in the hoop and axial directions and is among the strongest available non-metallic repair material on the market. The second component is the binding force in the system. This system is an impregnated urethane resin, which allows for uniform loading throughout the entire wrap. Our third component, for repairs that require surfaces to be modified (e.g. heavy pitting or irregular shapes); the high modulus filler can be applied. These components form a composite system that is stronger than steel. The structural system forms a pipe around a pipe, and each successive wrap increases the pressure rating. Minimal creep ensures a long service life.
LEAK TERMINATOR
COMPRESSION FILM / PERFORATOR
Heavy gauge film material used to compress all composites during installation. Using IR-COMP film ensures the full strength of the composite around the pipe during the installation. Perforation in the IR-COMP is required to release CO2 gas buildup that occurs during the cure of Titanium HydroWrap.
Standard Sizes:
5 in X 200 ft (12.7 cm X 61 m) 12 in X 700 ft (30.5 cm X 213 m)
aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap aquawrap
IRIDIUM PEEL-PLY
Iridium Peel-Ply is a release fabric made of finely woven porous Nylon fabric. It is used to vent excess resin and provide compression around the composite repair and ensures the full strength of the composite around the pipe during the installation. The peel ply can prevent contamination of the repair surface up to the time it is removed. The peel ply should tear a very thin layer of resin from the surface of the composite to create a fresh clean anchor pattern surface ready to paint and avoid sanding.
Standard Size:
6 in X 55 yds (15 cm X 50 m)
